Home › Materials › Polypropylene (PP) Machining
Materials

Polypropylene (PP) Machining for Chemical, Electrical and Fixture Parts

PP is the lightest of the common engineering plastics and one of the cheapest to buy, which is why chemical tanks, plating jigs, insulating plates and work-holding fixtures end up in polypropylene. It is also soft, expands about ten times as much as steel per degree, and will not hold paint or adhesive without surface pre-treatment. Machining it well is mostly about holding it without squeezing it out of shape.

Request a Quote
Why ProtoTech

Machining PP without squeezing it out of tolerance

Soft material, controlled clamping

PP marks and deflects under clamp pressure that would be normal on aluminium. We clamp on sacrificial material or use vacuum where the wall is thin, and we check the part after unclamping rather than on the machine — a soft part can measure true while held and spring back once released.

Heat builds up faster than it leaves

Polypropylene conducts heat poorly, so cutting heat stays at the edge instead of leaving through the chip. Left alone it smears the surface and pushes the part around. We cut with sharp, high-rake tooling and air cooling, and rough and finish in separate passes so the part is not stressed twice in one setup.

Colour from the sheet, not from a gun

We machine the grey in. There is no paint layer to chip, no coating lead time and no adhesion risk on a plastic whose surface energy is half of what paint needs. The trade-off is honest: the shade reads close to the nominal colour but is not a measured colour-number match.

Technical data

PP Machining

Real capability windows — verified in-house, not estimated.

CapabilitySpecification
MaterialPolypropylene sheet — PP-H (homopolymer) and PP-C (copolymer)
Sheet sourceRöchling Polystone® P (PP-H and PP-C)
Typical tolerance±0.01 mm standard; ±0.005 mm on small parts where the drawing allows
Maximum workpiece800 × 1000 mm
Density0.90–0.91 g/cm³ — the lightest common engineering plastic
Chemical resistanceExcellent against acids, alkalis and most solvents; attacked by aromatic and chlorinated hydrocarbons
TemperatureContinuous around 100 °C for PP-H; lower under sustained load
ColourNatural, black and grey grades — grey sheet close to RAL 7032
ProcessesCNC milling, CNC turning
PackagingISO Class 7 cleanroom / ESD-safe
CertificatesISO 9001:2015 · IATF 16949:2016 · EN 10204 3.1
Prototype lead timeTypically 5–10 working days
Colour

Grey PP to RAL 7032 — what we actually do

RAL 7032 (Pebble Grey) is the standard shade on European electrical enclosures, control cabinets and machine frames. Customers who specify it usually have a grey powder-coated cabinet on the bench and need the plastic parts inside to sit in the same family of colour.

On a PP part it cannot be specified the way it is on steel. We do not coat the part — we machine the colour out of the sheet. Grey polypropylene reads close to RAL 7032, holds the shade through the body of the part, and cannot chip, because there is no coating to chip.

Three things to agree before you order

  • The shade is close, not a colour-number match. If your incoming inspection measures colour difference, ask for a sample plaque from the actual sheet lot before the batch is released.
  • No coating step means no coating lead time. There is no paint queue, no adhesion test and no risk of a low-surface-energy plastic shedding its finish after a few thermal cycles.
  • If the drawing demands a measured RAL match, the route changes. The part then has to be coated, PP has to be flame or plasma pre-treated first, and that process is placed with a qualified partner outside our plant — with the quality responsibility still on us.
Process

From Drawing to Delivered Part

1

Submit & Review

Send the drawing, the PP grade and the colour requirement. We confirm wall thickness, clamping strategy and whether the shade needs to be measured.

2

Quote & Material Plan

Quotation with the sheet grade and source stated, so your buyer can compare against a nominated brand rather than a generic “PP”.

3

Machine & Inspect

Rough and finish separated where the part is thin, dimensional report and material certificate on request.

4

Deliver & Support

ESD-safe or ISO Class 7 packaging, with the batch report tied to the same characteristics on repeat orders.

FAQ

Frequently asked questions

Yes, with one limitation worth knowing. RAL 7032 is a powder-coating shade, not a standard for plastic colour. We machine grey polypropylene sheet that reads close to RAL 7032 next to a coated cabinet, but we do not claim a measured colour-number match. If your drawing needs one, the part has to be coated, and PP must be flame or plasma pre-treated before anything will adhere.
800 × 1000 mm. Above roughly 300 mm, thermal expansion starts to dominate the tolerance: PP moves about 0.15 mm per metre per degree, so a large part measured cold and checked warm will not agree with itself. We agree the inspection temperature with you on large parts rather than quoting a number that cannot be held.
±0.01 mm is our standard window on plastics, and ±0.005 mm is achievable on small parts where the geometry is rigid enough and the drawing allows it. PP is soft and thin walls relax after machining, so where the part justifies it we rough, stress-relieve and finish in separate operations.
PP has a surface energy around 29 mN/m, well below what a coating needs to wet and bond. Without flame or plasma treatment the paint fails adhesion testing, usually after a few thermal cycles rather than on the first day. That is why we machine the colour into the part from the sheet instead of painting it on.
Yes. Customers often nominate the sheet brand themselves and Röchling material is what we buy most often. Send the grade and we machine to your drawing. If you supply the sheet, we agree the clamping and cleanup allowance before the first cut, because PP sheet thickness varies more than metal stock.
Start a project

Request a Quote

Tell us about your program. The fields below help our engineering team prioritize recurring, long-term supply programs with equipment manufacturers.

What happens after you send your files

  • Within 1 business day an engineer — not a salesperson — reviews your drawings and replies.
  • DFM review: tolerances, material and risk flags, before any cutting begins.
  • Your quote includes a material-verification plan: grade, EN/DIN check, certificate strategy.

Critical features are verified in house · material chemistry confirmed by spectrometer · EN 10204 3.1 certificates available.

Prefer email? Write to us directly at info@prototech-machining.com

Recurring programs and orders of 1,000+ pcs are prioritised by our engineering team.
The number of parts per order — it lets us price tooling and batch setup correctly instead of guessing at a range.
Several different parts? Email your list and drawings to ellie@prototech-machining.com and we will quote them together.
e.g. 120 pcs · 6061-T6 aluminium · black anodise · mates with bracket PT-1042
Your files stay yours.
Drawings and CAD files are used only to quote and manufacture your parts. They are not shared with third parties, and we sign an NDA on request — even before you send anything.
Built for qualified programs.
Our form captures production type, annual quantity and project status up front — so we can focus engineering resources on long-term supply relationships, not one-off inquiries.
Need engineering input first?
Talk to our team about special materials, tolerances or a failed-supplier recovery before you send drawings.
↑